Location

Location ANSS

2019/04/28 17:03:16 39.797 -117.494 4.0 4.0 Nevada

Focal Mechanism

 USGS/SLU Moment Tensor Solution
 ENS  2019/04/28 17:03:16:0  39.80 -117.49   4.0 4.0 Nevada
 
 Stations used:
   BK.DANT BK.HATC CI.GRA IM.NV31 IW.MFID LB.TPH NC.AFD NC.LDH 
   NC.LMC NC.MDPB NN.CMK6 NN.DSP NN.GMN NN.GWY NN.LHV NN.MPK 
   NN.MZPB NN.PAH NN.PIO NN.PNT NN.Q09A NN.REDF NN.RYN NN.S11A 
   NN.SHP NN.SPR3 NN.WAK NN.WDEM NN.WLDB SN.HEL US.DUG US.ELK 
   US.TPNV US.WVOR UU.BGU UU.PSUT UU.SWUT UU.VRUT UW.IRON 
 
 Filtering commands used:
   cut o DIST/3.3 -40 o DIST/3.3 +50
   rtr
   taper w 0.1
   hp c 0.03 n 3 
   lp c 0.10 n 3 
 
 Best Fitting Double Couple
  Mo = 8.32e+21 dyne-cm
  Mw = 3.88 
  Z  = 12 km
  Plane   Strike  Dip  Rake
   NP1      250    50   -70
   NP2       40    44   -112
  Principal Axes:
   Axis    Value   Plunge  Azimuth
    T   8.32e+21      3     326
    N   0.00e+00     15      57
    P  -8.32e+21     74     225

 Moment Tensor: (dyne-cm)
    Component   Value
       Mxx     5.40e+21
       Mxy    -4.14e+21
       Mxz     1.90e+21
       Myy     2.30e+21
       Myz     1.25e+21
       Mzz    -7.70e+21
                                                     
                                                     
                                                     
                                                     
                     ##############                  
                 T ####################              
              ##   #######################           
             #############################-          
           ################################--        
          #################---------------#---       
         #############---------------------###-      
        ###########------------------------#####     
        ########---------------------------#####     
       #######----------------------------#######    
       #####------------------------------#######    
       ####-------------   --------------########    
       ###-------------- P -------------#########    
        #---------------   ------------#########     
        #-----------------------------##########     
         ---------------------------###########      
          ------------------------############       
           ---------------------#############        
             ----------------##############          
              ----------##################           
                 ######################              
                     ##############                  
                                                     
                                                     
                                                     
 Global CMT Convention Moment Tensor:
      R          T          P
 -7.70e+21   1.90e+21  -1.25e+21 
  1.90e+21   5.40e+21   4.14e+21 
 -1.25e+21   4.14e+21   2.30e+21 


Details of the solution is found at

http://www.eas.slu.edu/eqc/eqc_mt/MECH.NA/20190428170316/index.html
        

Preferred Solution

The preferred solution from an analysis of the surface-wave spectral amplitude radiation pattern, waveform inversion and first motion observations is

      STK = 250
      DIP = 50
     RAKE = -70
       MW = 3.88
       HS = 12.0

The NDK file is 20190428170316.ndk The waveform inversion is preferred.

Moment Tensor Comparison

The following compares this source inversion to others
SLU
 USGS/SLU Moment Tensor Solution
 ENS  2019/04/28 17:03:16:0  39.80 -117.49   4.0 4.0 Nevada
 
 Stations used:
   BK.DANT BK.HATC CI.GRA IM.NV31 IW.MFID LB.TPH NC.AFD NC.LDH 
   NC.LMC NC.MDPB NN.CMK6 NN.DSP NN.GMN NN.GWY NN.LHV NN.MPK 
   NN.MZPB NN.PAH NN.PIO NN.PNT NN.Q09A NN.REDF NN.RYN NN.S11A 
   NN.SHP NN.SPR3 NN.WAK NN.WDEM NN.WLDB SN.HEL US.DUG US.ELK 
   US.TPNV US.WVOR UU.BGU UU.PSUT UU.SWUT UU.VRUT UW.IRON 
 
 Filtering commands used:
   cut o DIST/3.3 -40 o DIST/3.3 +50
   rtr
   taper w 0.1
   hp c 0.03 n 3 
   lp c 0.10 n 3 
 
 Best Fitting Double Couple
  Mo = 8.32e+21 dyne-cm
  Mw = 3.88 
  Z  = 12 km
  Plane   Strike  Dip  Rake
   NP1      250    50   -70
   NP2       40    44   -112
  Principal Axes:
   Axis    Value   Plunge  Azimuth
    T   8.32e+21      3     326
    N   0.00e+00     15      57
    P  -8.32e+21     74     225

 Moment Tensor: (dyne-cm)
    Component   Value
       Mxx     5.40e+21
       Mxy    -4.14e+21
       Mxz     1.90e+21
       Myy     2.30e+21
       Myz     1.25e+21
       Mzz    -7.70e+21
                                                     
                                                     
                                                     
                                                     
                     ##############                  
                 T ####################              
              ##   #######################           
             #############################-          
           ################################--        
          #################---------------#---       
         #############---------------------###-      
        ###########------------------------#####     
        ########---------------------------#####     
       #######----------------------------#######    
       #####------------------------------#######    
       ####-------------   --------------########    
       ###-------------- P -------------#########    
        #---------------   ------------#########     
        #-----------------------------##########     
         ---------------------------###########      
          ------------------------############       
           ---------------------#############        
             ----------------##############          
              ----------##################           
                 ######################              
                     ##############                  
                                                     
                                                     
                                                     
 Global CMT Convention Moment Tensor:
      R          T          P
 -7.70e+21   1.90e+21  -1.25e+21 
  1.90e+21   5.40e+21   4.14e+21 
 -1.25e+21   4.14e+21   2.30e+21 


Details of the solution is found at

http://www.eas.slu.edu/eqc/eqc_mt/MECH.NA/20190428170316/index.html
	

Magnitudes

mLg Magnitude


(a) mLg computed using the IASPEI formula; (b) mLg residuals ; the values used for the trimmed mean are indicated.

ML Magnitude


(a) ML computed using the IASPEI formula for Horizontal components; (b) ML residuals computed using a modified IASPEI formula that accounts for path specific attenuation; the values used for the trimmed mean are indicated. The ML relation used for each figure is given at the bottom of each plot.


(a) ML computed using the IASPEI formula for Vertical components (research); (b) ML residuals computed using a modified IASPEI formula that accounts for path specific attenuation; the values used for the trimmed mean are indicated. The ML relation used for each figure is given at the bottom of each plot.

Context

The next figure presents the focal mechanism for this earthquake (red) in the context of other events (blue) in the SLU Moment Tensor Catalog which are within ± 0.5 degrees of the new event. This comparison is shown in the left panel of the figure. The right panel shows the inferred direction of maximum compressive stress and the type of faulting (green is strike-slip, red is normal, blue is thrust; oblique is shown by a combination of colors).

Waveform Inversion using wvfgrd96

The focal mechanism was determined using broadband seismic waveforms. The location of the event and the and stations used for the waveform inversion are shown in the next figure.
Location of broadband stations used for waveform inversion

The program wvfgrd96 was used with good traces observed at short distance to determine the focal mechanism, depth and seismic moment. This technique requires a high quality signal and well determined velocity model for the Green functions. To the extent that these are the quality data, this type of mechanism should be preferred over the radiation pattern technique which requires the separate step of defining the pressure and tension quadrants and the correct strike.

The observed and predicted traces are filtered using the following gsac commands:

cut o DIST/3.3 -40 o DIST/3.3 +50
rtr
taper w 0.1
hp c 0.03 n 3 
lp c 0.10 n 3 
The results of this grid search from 0.5 to 19 km depth are as follow:

           DEPTH  STK   DIP  RAKE   MW    FIT
WVFGRD96    1.0    55    45    90   3.53 0.2168
WVFGRD96    2.0    55    45    90   3.65 0.2505
WVFGRD96    3.0   100    85    60   3.64 0.2223
WVFGRD96    4.0    75    90    65   3.68 0.2763
WVFGRD96    5.0   245    80   -70   3.71 0.3227
WVFGRD96    6.0   245    80   -65   3.72 0.3548
WVFGRD96    7.0   240    75   -70   3.73 0.3775
WVFGRD96    8.0   240    75   -75   3.81 0.3924
WVFGRD96    9.0   240    65   -80   3.84 0.4086
WVFGRD96   10.0   245    60   -75   3.85 0.4210
WVFGRD96   11.0   250    50   -70   3.87 0.4266
WVFGRD96   12.0   250    50   -70   3.88 0.4273
WVFGRD96   13.0   255    50   -65   3.89 0.4221
WVFGRD96   14.0   255    50   -65   3.89 0.4120
WVFGRD96   15.0   255    45   -65   3.90 0.3977
WVFGRD96   16.0   260    45   -55   3.91 0.3819
WVFGRD96   17.0   265    45   -50   3.92 0.3648
WVFGRD96   18.0   265    40   -50   3.92 0.3471
WVFGRD96   19.0   270    35   -45   3.93 0.3305
WVFGRD96   20.0   270    35   -45   3.93 0.3138
WVFGRD96   21.0   270    30   -45   3.95 0.3000
WVFGRD96   22.0   270    30   -45   3.95 0.2846
WVFGRD96   23.0   275    30   -40   3.96 0.2694
WVFGRD96   24.0   270    25   -45   3.96 0.2544
WVFGRD96   25.0   275    25   -40   3.97 0.2397
WVFGRD96   26.0   275    25   -40   3.97 0.2249
WVFGRD96   27.0   275    25   -40   3.98 0.2100
WVFGRD96   28.0   280    25   -35   3.98 0.1950
WVFGRD96   29.0   275    20   -40   3.98 0.1802

The best solution is

WVFGRD96   12.0   250    50   -70   3.88 0.4273

The mechanism correspond to the best fit is
Figure 1. Waveform inversion focal mechanism

The best fit as a function of depth is given in the following figure:

Figure 2. Depth sensitivity for waveform mechanism

The comparison of the observed and predicted waveforms is given in the next figure. The red traces are the observed and the blue are the predicted. Each observed-predicted component is plotted to the same scale and peak amplitudes are indicated by the numbers to the left of each trace. A pair of numbers is given in black at the right of each predicted traces. The upper number it the time shift required for maximum correlation between the observed and predicted traces. This time shift is required because the synthetics are not computed at exactly the same distance as the observed and because the velocity model used in the predictions may not be perfect. A positive time shift indicates that the prediction is too fast and should be delayed to match the observed trace (shift to the right in this figure). A negative value indicates that the prediction is too slow. The lower number gives the percentage of variance reduction to characterize the individual goodness of fit (100% indicates a perfect fit).

The bandpass filter used in the processing and for the display was

cut o DIST/3.3 -40 o DIST/3.3 +50
rtr
taper w 0.1
hp c 0.03 n 3 
lp c 0.10 n 3 
Figure 3. Waveform comparison for selected depth. Red: observed; Blue - predicted. The time shift with respect to the model prediction is indicated. The percent of fit is also indicated.
Focal mechanism sensitivity at the preferred depth. The red color indicates a very good fit to thewavefroms. Each solution is plotted as a vector at a given value of strike and dip with the angle of the vector representing the rake angle, measured, with respect to the upward vertical (N) in the figure.

A check on the assumed source location is possible by looking at the time shifts between the observed and predicted traces. The time shifts for waveform matching arise for several reasons:

Assuming only a mislocation, the time shifts are fit to a functional form:

 Time_shift = A + B cos Azimuth + C Sin Azimuth

The time shifts for this inversion lead to the next figure:

The derived shift in origin time and epicentral coordinates are given at the bottom of the figure.

Discussion

Acknowledgements

Thanks also to the many seismic network operators whose dedication make this effort possible: University of Nevada Reno, University of Alaska, University of Washington, Oregon State University, University of Utah, Montana Bureas of Mines, UC Berkely, Caltech, UC San Diego, Saint Louis University, University of Memphis, Lamont Doherty Earth Observatory, the Iris stations and the Transportable Array of EarthScope.

Velocity Model

The WUS.model used for the waveform synthetic seismograms and for the surface wave eigenfunctions and dispersion is as follows:

MODEL.01
Model after     8 iterations
ISOTROPIC
KGS
FLAT EARTH
1-D
CONSTANT VELOCITY
LINE08
LINE09
LINE10
LINE11
      H(KM)   VP(KM/S)   VS(KM/S) RHO(GM/CC)         QP         QS       ETAP       ETAS      FREFP      FREFS
     1.9000     3.4065     2.0089     2.2150  0.302E-02  0.679E-02   0.00       0.00       1.00       1.00    
     6.1000     5.5445     3.2953     2.6089  0.349E-02  0.784E-02   0.00       0.00       1.00       1.00    
    13.0000     6.2708     3.7396     2.7812  0.212E-02  0.476E-02   0.00       0.00       1.00       1.00    
    19.0000     6.4075     3.7680     2.8223  0.111E-02  0.249E-02   0.00       0.00       1.00       1.00    
     0.0000     7.9000     4.6200     3.2760  0.164E-10  0.370E-10   0.00       0.00       1.00       1.00    

Quality Control

Here we tabulate the reasons for not using certain digital data sets

The following stations did not have a valid response files:

Last Changed Sun Apr 28 13:51:11 CDT 2019