Location

2012/06/25 04:04:56 47.349 -113.135 23.8 4.70 Montana

Arrival Times (from USGS)

Arrival time list

Felt Map

USGS Felt map for this earthquake

USGS Felt reports main page

Focal Mechanism

 USGS/SLU Moment Tensor Solution
 ENS  2012/06/25 04:04:56:2  47.35 -113.14  23.8 4.7 Montana
 
 Stations used:
   IW.FXWY MB.JTMT US.BOZ US.EGMT US.MSO WY.YMR WY.YPP WY.YUF 
 
 Filtering commands used:
   hp c 0.02 n 3
   lp c 0.08 n 3
 
 Best Fitting Double Couple
  Mo = 1.58e+21 dyne-cm
  Mw = 3.40 
  Z  = 21 km
  Plane   Strike  Dip  Rake
   NP1      189    46   -80
   NP2      355    45   -100
  Principal Axes:
   Axis    Value   Plunge  Azimuth
    T   1.58e+21      0     272
    N   0.00e+00      7       2
    P  -1.58e+21     83     179

 Moment Tensor: (dyne-cm)
    Component   Value
       Mxx    -2.19e+19
       Mxy    -5.61e+19
       Mxz     1.94e+20
       Myy     1.58e+21
       Myz    -1.70e+19
       Mzz    -1.56e+21
                                                     
                                                     
                                                     
                                                     
                     ##############                  
                 #########-----########              
              ##########---------#########           
             #########-------------########          
           ##########---------------#########        
          ##########-----------------#########       
         ##########-------------------#########      
        ##########--------------------##########     
        ##########---------------------#########     
         ########----------------------##########    
       T ########----------------------##########    
         ########----------   ---------##########    
       ##########---------- P ---------##########    
        #########----------   ---------#########     
        #########----------------------#########     
         ########---------------------#########      
          ########--------------------########       
           #######-------------------########        
             ######-----------------#######          
              ######---------------#######           
                 #####------------#####              
                     ##---------###                  
                                                     
                                                     
                                                     
 Global CMT Convention Moment Tensor:
      R          T          P
 -1.56e+21   1.94e+20   1.70e+19 
  1.94e+20  -2.19e+19   5.61e+19 
  1.70e+19   5.61e+19   1.58e+21 


Details of the solution is found at

http://www.eas.slu.edu/eqc/eqc_mt/MECH.NA/20120625040456/index.html
        

Preferred Solution

The preferred solution from an analysis of the surface-wave spectral amplitude radiation pattern, waveform inversion and first motion observations is

      STK = -5
      DIP = 45
     RAKE = -100
       MW = 3.40
       HS = 21.0

The NDK file is 20120625040456.ndk The waveform inversion is preferred.

Moment Tensor Comparison

The following compares this source inversion to others
SLU
 USGS/SLU Moment Tensor Solution
 ENS  2012/06/25 04:04:56:2  47.35 -113.14  23.8 4.7 Montana
 
 Stations used:
   IW.FXWY MB.JTMT US.BOZ US.EGMT US.MSO WY.YMR WY.YPP WY.YUF 
 
 Filtering commands used:
   hp c 0.02 n 3
   lp c 0.08 n 3
 
 Best Fitting Double Couple
  Mo = 1.58e+21 dyne-cm
  Mw = 3.40 
  Z  = 21 km
  Plane   Strike  Dip  Rake
   NP1      189    46   -80
   NP2      355    45   -100
  Principal Axes:
   Axis    Value   Plunge  Azimuth
    T   1.58e+21      0     272
    N   0.00e+00      7       2
    P  -1.58e+21     83     179

 Moment Tensor: (dyne-cm)
    Component   Value
       Mxx    -2.19e+19
       Mxy    -5.61e+19
       Mxz     1.94e+20
       Myy     1.58e+21
       Myz    -1.70e+19
       Mzz    -1.56e+21
                                                     
                                                     
                                                     
                                                     
                     ##############                  
                 #########-----########              
              ##########---------#########           
             #########-------------########          
           ##########---------------#########        
          ##########-----------------#########       
         ##########-------------------#########      
        ##########--------------------##########     
        ##########---------------------#########     
         ########----------------------##########    
       T ########----------------------##########    
         ########----------   ---------##########    
       ##########---------- P ---------##########    
        #########----------   ---------#########     
        #########----------------------#########     
         ########---------------------#########      
          ########--------------------########       
           #######-------------------########        
             ######-----------------#######          
              ######---------------#######           
                 #####------------#####              
                     ##---------###                  
                                                     
                                                     
                                                     
 Global CMT Convention Moment Tensor:
      R          T          P
 -1.56e+21   1.94e+20   1.70e+19 
  1.94e+20  -2.19e+19   5.61e+19 
  1.70e+19   5.61e+19   1.58e+21 


Details of the solution is found at

http://www.eas.slu.edu/eqc/eqc_mt/MECH.NA/20120625040456/index.html
	

Magnitudes

ML Magnitude


(a) ML computed using the IASPEI formula for Horizontal components; (b) ML residuals computed using a modified IASPEI formula that accounts for path specific attenuation; the values used for the trimmed mean are indicated. The ML relation used for each figure is given at the bottom of each plot.


(a) ML computed using the IASPEI formula for Vertical components (research); (b) ML residuals computed using a modified IASPEI formula that accounts for path specific attenuation; the values used for the trimmed mean are indicated. The ML relation used for each figure is given at the bottom of each plot.

Context

The next figure presents the focal mechanism for this earthquake (red) in the context of other events (blue) in the SLU Moment Tensor Catalog which are within ± 0.5 degrees of the new event. This comparison is shown in the left panel of the figure. The right panel shows the inferred direction of maximum compressive stress and the type of faulting (green is strike-slip, red is normal, blue is thrust; oblique is shown by a combination of colors).

Waveform Inversion

The focal mechanism was determined using broadband seismic waveforms. The location of the event and the and stations used for the waveform inversion are shown in the next figure.
Location of broadband stations used for waveform inversion

The program wvfgrd96 was used with good traces observed at short distance to determine the focal mechanism, depth and seismic moment. This technique requires a high quality signal and well determined velocity model for the Green functions. To the extent that these are the quality data, this type of mechanism should be preferred over the radiation pattern technique which requires the separate step of defining the pressure and tension quadrants and the correct strike.

The observed and predicted traces are filtered using the following gsac commands:

hp c 0.02 n 3
lp c 0.08 n 3
The results of this grid search from 0.5 to 19 km depth are as follow:

           DEPTH  STK   DIP  RAKE   MW    FIT
WVFGRD96    0.5   175    40    90   2.88 0.2369
WVFGRD96    1.0   265    90     0   2.94 0.2491
WVFGRD96    2.0    85    75    15   3.07 0.3076
WVFGRD96    3.0    85    75    15   3.14 0.3102
WVFGRD96    4.0    80    70    -5   3.15 0.2780
WVFGRD96    5.0   285    25    -5   3.15 0.2922
WVFGRD96    6.0   280    25   -10   3.17 0.3266
WVFGRD96    7.0   275    25   -15   3.18 0.3524
WVFGRD96    8.0   280    20    -5   3.25 0.3674
WVFGRD96    9.0   205    85    65   3.26 0.3829
WVFGRD96   10.0   205    80    60   3.27 0.3951
WVFGRD96   11.0    30    60   -70   3.31 0.4164
WVFGRD96   12.0    25    55   -70   3.31 0.4411
WVFGRD96   13.0    15    50   -80   3.32 0.4626
WVFGRD96   14.0    15    50   -80   3.33 0.4813
WVFGRD96   15.0    10    45   -85   3.34 0.4970
WVFGRD96   16.0     5    45   -90   3.35 0.5099
WVFGRD96   17.0   185    45   -85   3.35 0.5204
WVFGRD96   18.0   190    45   -80   3.37 0.5280
WVFGRD96   19.0   190    45   -80   3.38 0.5346
WVFGRD96   20.0   190    45   -80   3.39 0.5386
WVFGRD96   21.0    -5    45  -100   3.40 0.5404
WVFGRD96   22.0   195    45   -75   3.41 0.5402
WVFGRD96   23.0   195    45   -75   3.42 0.5385
WVFGRD96   24.0   195    45   -75   3.43 0.5352
WVFGRD96   25.0   195    45   -75   3.43 0.5300
WVFGRD96   26.0   200    45   -70   3.44 0.5246
WVFGRD96   27.0   200    45   -70   3.45 0.5183
WVFGRD96   28.0   205    45   -65   3.46 0.5114
WVFGRD96   29.0   205    45   -65   3.47 0.5039

The best solution is

WVFGRD96   21.0    -5    45  -100   3.40 0.5404

The mechanism corresponding to the best fit is
Figure 1. Waveform inversion focal mechanism

The best fit as a function of depth is given in the following figure:

Figure 2. Depth sensitivity for waveform mechanism

The comparison of the observed and predicted waveforms is given in the next figure. The red traces are the observed and the blue are the predicted. Each observed-predicted component is plotted to the same scale and peak amplitudes are indicated by the numbers to the left of each trace. A pair of numbers is given in black at the right of each predicted traces. The upper number it the time shift required for maximum correlation between the observed and predicted traces. This time shift is required because the synthetics are not computed at exactly the same distance as the observed and because the velocity model used in the predictions may not be perfect. A positive time shift indicates that the prediction is too fast and should be delayed to match the observed trace (shift to the right in this figure). A negative value indicates that the prediction is too slow. The lower number gives the percentage of variance reduction to characterize the individual goodness of fit (100% indicates a perfect fit).

The bandpass filter used in the processing and for the display was

hp c 0.02 n 3
lp c 0.08 n 3
Figure 3. Waveform comparison for selected depth
Focal mechanism sensitivity at the preferred depth. The red color indicates a very good fit to thewavefroms. Each solution is plotted as a vector at a given value of strike and dip with the angle of the vector representing the rake angle, measured, with respect to the upward vertical (N) in the figure.

A check on the assumed source location is possible by looking at the time shifts between the observed and predicted traces. The time shifts for waveform matching arise for several reasons:

Assuming only a mislocation, the time shifts are fit to a functional form:

 Time_shift = A + B cos Azimuth + C Sin Azimuth

The time shifts for this inversion lead to the next figure:

The derived shift in origin time and epicentral coordinates are given at the bottom of the figure.

Discussion

Acknowledgements

Thanks also to the many seismic network operators whose dedication make this effort possible: University of Nevada Reno, University of Alaska, University of Washington, Oregon State University, University of Utah, Montana Bureas of Mines, UC Berkely, Caltech, UC San Diego, Saint Louis University, University of Memphis, Lamont Doherty Earth Observatory, the Iris stations and the Transportable Array of EarthScope.

Velocity Model

The WUS model used for the waveform synthetic seismograms and for the surface wave eigenfunctions and dispersion is as follows:

MODEL.01
Model after     8 iterations
ISOTROPIC
KGS
FLAT EARTH
1-D
CONSTANT VELOCITY
LINE08
LINE09
LINE10
LINE11
      H(KM)   VP(KM/S)   VS(KM/S) RHO(GM/CC)         QP         QS       ETAP       ETAS      FREFP      FREFS
     1.9000     3.4065     2.0089     2.2150  0.302E-02  0.679E-02   0.00       0.00       1.00       1.00    
     6.1000     5.5445     3.2953     2.6089  0.349E-02  0.784E-02   0.00       0.00       1.00       1.00    
    13.0000     6.2708     3.7396     2.7812  0.212E-02  0.476E-02   0.00       0.00       1.00       1.00    
    19.0000     6.4075     3.7680     2.8223  0.111E-02  0.249E-02   0.00       0.00       1.00       1.00    
     0.0000     7.9000     4.6200     3.2760  0.164E-10  0.370E-10   0.00       0.00       1.00       1.00    

Quality Control

Here we tabulate the reasons for not using certain digital data sets

The following stations did not have a valid response files:

Last Changed Mon Dec 7 00:24:59 CST 2015